SKU: 10424141034

PRO-TECH PLUNGE CUTTING BALL 1' X 2' 1/2'SHANK KP216461

Sale price$244.96 Regular price$272.18
Save 10%

Pay in installments of $68.05 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 3 - Aug 8

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

PRO-TECH PLUNGE CUTTING BALL 1' X 2' 1/2'SHANK KP216461Ball cutting router bit Carbide Tipped Cut channels for pipes or cables using the ball end bit. The profile requires the cut to be made in a single pass. To reduce stress on the bit, cut an initial groove using a straight bit matching the diameter dimension of the ball end bit. Cut channels for pipes or cables using this ball end bit. Uses include: 2 Flute Industrial quality Carbide tipped To reduce stress on the bit, cut an initial groove using a

Ball cutting router bit

Carbide Tipped

Cut channels for pipes or cables using the ball end bit. The profile requires the cut to be made in a single pass. To reduce stress on the bit, cut an initial groove using a straight bit matching the diameter dimension of the ball end bit. Cut channels for pipes or cables using this ball end bit.

Uses include:

  • 2-Flute
  • Industrial quality
  •  Carbide tipped

 

To reduce stress on the bit, cut an initial groove using a straight bit matching the width dimension of the ball end bit. Profile is used as a conduit for cables and pipes. Note: The profile requires the cut to be made in a single pass.

 

This router bit has a 12,70 mm shank (shaft) that will fit most large routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.

 

PRO-TECH router bits are manufactured in Taiwan.

 

consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection clean and scratch free
  • Hearing protection quality earmuffs
  • Dust masks discard old and dirty masks
  • Gloves for easy handling of material and hand protection
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

To use router bits safely (and to get the best results from your router), the router bits need to be installed properly into the router's collet. Improper installation of your bits can cause excessive chatter and could increase the likelihood that the bits will break when in use. 

Clean and sharp

First of all, before beginning any routing operation, check your bits to make sure that they are clean, relatively free of pitch, and most of all, sharp. If the bit is dull, chipped, is excessively burned or has any other defect, it should be sharpened or replaced before use. 

Correct collet and collet nut fit

Most router collets have a recess (groove) that needs to click into a circlip that resides inside the collet nut. Failing to ensure that the collet 'clicked' into the collet nut will cause you to struggle to remove the router bit after tightening. This could cause the collet to break or be removed by a technical repair centre.

 

Correct fit inside the collet

When installing the bit into the collet, do not tighten the collet with the bit 'seated.' Instead, insert the bit until the shank (bit shaft) reaches the bottom of the collet, then ease it out about 2 mm before tightening the collet.

When the bit is tightened, there should be no less than  2/3 's of the length of the shank in the collet. If your bit has a shank that is too short, then the bit should be replaced. 

 

Safety gear

There are a few other safety measures to keep in mind whenever you use your router. First of all, remember to always wear appropriate safety gear as indicated above.

Correct speed setting

Second, be sure to set your router to the proper speed for your router bit. Setting your router to an incorrect speed will not only affect the router's performance, but also can cause the bit to break much more easily and even cause bodily harm. The speed at which a router bit turns can be important. The typical router runs at about 22,000 rpm, which is fine for most bits. But as the diameter of the bit increases, you ll want to slow things down.

Also, before beginning any routing operation, be certain that you give the router's motor time to come up to full speed for the chosen setting. Beginning to cut before the bit is at full speed can give less than desired results. 

Observe the following at all times

  • Wear a protective face shield or Safety Glasses to prevent eye and face injury.
  • Wear ear plugs or ear muffs to protect your hearing.
  • Use a respirator or dust mask to give protection from dust particles. Wood dust may remain in the air for hours after using power tools.
  • Always read and follow router operator's manual instructions.
  • Make sure that router rpm's and the bit selected match.
  • Dress properly. Wear short sleeves, no loose fitting clothes, proper footwear and no jewellery. Tie back long hair.
  • Always be sure the router is unplugged before replacing bits and that the switch is off before connecting the router.
  • Be sure the router bit has completing stopped spinning before sitting the router down.
  • Be sure bits, clamps and attachments are secure before starting up.
  • Keep children, pets and visitors at a safe distance.
  • Be especially cautious when working small pieces.
  • Keep hands and fingers away from revolving bits and cutters.
  • Do not operate routers in moist or wet areas.
  • Always grip tool tightly and be prepared at start-up to resist the motor torque.
  • When using a router table, make sure on/off switch is easily accessible.
  • Learn the sound of your router and shut it off at any unfamiliar sounds or irregularities.
    Never start the router with the bit in contact with the material.
  • Always feed in the proper direction, against the direction of bit rotation.
  • Maintain equipment. Replace worn parts, discard worn-out bits and check router periodically. Clean parts with appropriate solvents.
  • Don't operate a tool if you are tired or under the influence of medication, drugs, alcohol or while smoking.
  • Check wood for nails, screws or loose knots before routing.
  • Keep your mind on your work, avoid distractions, work at a comfortable pace and stop before you get tired.

Do a dry run

  • Place the router on the final work surface and test you cut by moving the router over the whole are to cut with THE ROUTER SWITCHED OFF
  • You do not want to waste an expensive piece of wood
  • You do not want to start all over
  • Never met anyone with spare fingers - SAFETY
Part No. Shank dia. Cutting width Cutting Height Radius
KP216461 1/2 inch 1 inch 1 inch used according
to width
12.70 mm 25.40 mm 25.40 mm

 

Length of Shank: 32 mm

 

 



KP216461Router Bits > Plunge Cutting Grooving Bits > Plunge Ball
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 10424141034

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.3 ★★★★★
Based on 26 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
M
Verified Purchase
MELODY DELONG
Belleville, US
★★★★★ 1
This is not a safe indestructible toy
DO NOT BUY! My 22 lb doodle destroyed this within the hour. He had all the nubs of two of the rings completely chewed off and was chewing them like gum. He is only 9 months old.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 13, 2026
K
Verified Purchase
Kallann
Cuba, US
★★★★★ 5
Super cute! Really quiet chewer.
Super cute and durable for our boxer puppy, it is for sure puppy sized. Super light so he can still toss it around and I like that it doesn’t have any plastic smell to it.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 27, 2026
N
Verified Purchase
nina w.
Boise, US
★★★★★ 3
Not for super chewers
My doodle puppy chewed the rings off. Definitely not made for a super chewer
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 21, 2026
T
Verified Purchase
Tracy Schletzbaum
Lowell, US
★★★★★ 4
Ok for an aggressive chewer but not the best
Color: Pink
O Jane an aggressive chewer. This has held up ok. But she still occasionally gets pieces chewed off.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 2, 2026
S
Verified Purchase
sabrina island
Draper, US
★★★★★ 5
She has torn up all her toys but not this one
Color: Pink
My dog loves this toy
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 2, 2026

recommand products