94.5-97 7.3L CNC Fab OBS HPOP Line Kit - 424001

94.5-97 7.3L CNC Fab OBS HPOP Line Kit - 424001CNC Fabrication High Pressure Oil Pump (HPOP) Line Kit Late 19941997 7. 3L Powerstroke Made in the USA Replace worn, high mileage OEM HPOP lines with this upgraded CNC Fabrication HPOP line kit, designed specifically for late 19941997 7. 3L Powerstroke engines. These lines offer increased reliability, higher pressure capability, and improved routing compared to factory hoses. Built using top of the line Aeroquip hose with DuPont Teflon lining, this

CNC Fabrication High Pressure Oil Pump (HPOP) Line Kit – Late 1994–1997 7.3L Powerstroke
Made in the USA

Replace worn, high-mileage OEM HPOP lines with this upgraded CNC Fabrication HPOP line kit, designed specifically for late 1994–1997 7.3L Powerstroke engines. These lines offer increased reliability, higher pressure capability, and improved routing compared to factory hoses.

Built using top-of-the-line Aeroquip hose with DuPont Teflon lining, this kit is engineered to handle the extreme pressures and temperatures of the 7.3’s high-pressure oil system.

Key Features:

• Direct OEM Replacement Upgrade – Replaces aging, failure-prone factory HPOP lines

• Upsized 3/8" Hose – Increased flow capacity and durability over stock lines

• Premium Aeroquip Hose – DuPont Teflon-lined for long service life

• Extreme Pressure Rated

  • 16,000 PSI burst pressure

  • 5,000 PSI working pressure @ 72°F

  • 3,000 PSI working pressure @ 400°F

• High Temperature Resistance – Rated up to 400°F

• Made in the USA

Kit Includes:

• (2) High-pressure oil hoses

• All required fittings for installation

Installation Notes:

• Line routing differs from OEM

• Driver Side Line routes like 1999–2003 models, utilizing the second oil galley port and routing around the engine lifting eyelet

• Passenger Side Line arches slightly over the front fuel bowl lid without interfering with fuel filter removal

• HPX crossover line (if installed) routes like 1999–2003 trucks using the third oil galley port from the front

Compatibility:

• Late 1994–1997 Ford 7.3L Powerstroke

This kit is ideal for anyone refreshing their high-pressure oil system or pairing with CNC Fabrication’s HPX crossover line for improved pressure balance and reduced system stress.

DOWNLOADABLE INSTALL INSTRUCTIONS

*Crossover line in the engine picture is not included*

INSTALLATION:  

Disconnect the battery grounds before installation to avoid accidentally arc'ing the line on the glow plug relay or the alternator charging lug. Use pictures from the product webpage for routing example. The fittings are marked with numbers to match installation location (see below for reference). After installation, be sure there are no other lines/wires that are touching the lines that could potentially rub through and damage either the HPOP line or the other line that may be touching it. Use a small section of wire loom protector or a larger piece or rubber hose to wrap around the contact point. Many will remove or bend the engine eyelet on the driver side as a precaution, but it is not necessary. Sealant is not necessary, but IF you choose to use any, use Loctite 680 or Permatex 64000 retaining compound (green) only on the fittings installed in the HPOP.  If you are unsure of installing yourself, seek out a competent and qualified technician to install the lines.

*REMOVE THE SPRING CHECKS IN THE PUMP UNDER THE STOCK FITTINGS, DO NOT RE-INSTALL*

HOSE IDENTIFICATION: 98.5-03 2 LINE-BOTH SIDES ARE SAME LENGTH. 94.5-97 2 LINE- PASSENGER IS LONGER OF THE 2. **FOR ANY 3 LINE KIT THE SHORTEST LINE IS THE CROSSOVER HOSE.

FITTING MARKINGS: 1- FRONT PUMP PORT 2- REAR PUMP PORT 3- DRIVER HEAD 4- 94.5-97 PASSENGER HEAD 5- 98.5-03 PASSENGER HEAD AND CROSSOVER **94.5-97 driver side fitting gets moved forward one port on the head to match 98.5-03**

Pump Fittings: 28FT/LBS • Head Fittings: 23FT/LBS • Hose Ends: 21FT/LBS