Water Pump Impeller Kit – Fits Honda 8/9.9/15/20 HP Outboards (Replaces 06192-ZW9-A30)

Water Pump Impeller Kit – Fits Honda 8/9.9/15/20 HP Outboards (Replaces 06192-ZW9-A30)Water Pump Impeller Kit Fits Honda 8 9. 9 15 20 HP Outboards (Replaces 06192 ZW9 A30) This water pump impeller repair kit provides the necessary components for servicing the water pump on Honda Marine 4 stroke 820 HP outboard motors. It is engineered to fit a wide range of models, including the BF8D, BF9. 9D, BF15D, BF20D, BFP8D, BFP9. 9D, BFP15D, and BFP20D series from all production years. This kit is a direct replacement for several OEM and

Water Pump Impeller Kit – Fits Honda 8/9.9/15/20 HP Outboards (Replaces 06192-ZW9-A30)

This water pump impeller repair kit provides the necessary components for servicing the water pump on Honda Marine 4-stroke 8–20 HP outboard motors. It is engineered to fit a wide range of models, including the BF8D, BF9.9D, BF15D, BF20D, BFP8D, BFP9.9D, BFP15D, and BFP20D series from all production years.

This kit is a direct replacement for several OEM and aftermarket part numbers, ensuring broad compatibility. It is designed to restore cooling system performance and prevent engine overheating caused by a worn or damaged impeller.

• Installation Method: Direct replacement for the original water pump components.
• Primary Components: Includes the water pump impeller, gasket, driveshaft key, and O-ring.
• Engine Compatibility: Specifically for Honda 4-Stroke outboards rated at 8, 9.9, 15, and 20 HP.

Part Number Cross-Reference

Use this table to confirm equivalent part numbers across OEM and aftermarket brands.

Compatible Engine Models

Confirm your engine model/year in the table below.

Technical Specifications

Package Contents

• 1 x Water Pump Impeller (19210-ZW9-A31/19210-ZW9-A32)
• 1 x Impeller Gasket (19232-ZW9-000)
• 1 x Impeller Key, Driveshaft (90752-ZW9-A30)
• 1 x O-Ring (91301-ZG3-000)

Explosion Diagram

Installation Guide

1. Disconnect the negative battery cable to prevent accidental starting.
2. Place the outboard in neutral and remove the bolts securing the lower unit (gearcase) to the engine's midsection.
3. Carefully lower and separate the gearcase from the driveshaft housing.
4. Locate the water pump housing on top of the gearcase and remove its mounting bolts.
5. Lift the housing to expose the old impeller. Note the rotational direction of the existing impeller vanes.
6. Remove the old impeller, driveshaft key, O-ring, and gasket. Thoroughly clean all mating surfaces.
7. Install the new O-ring and place the new gasket onto the gearcase.
8. Insert the new impeller key into the driveshaft slot. Slide the new impeller down the shaft while turning it clockwise to seat the vanes correctly inside the pump cup.
9. Reinstall the water pump housing and tighten the bolts to the manufacturer's specified torque.
10. Carefully guide the driveshaft and shift shaft back into the engine as you reinstall the lower unit. Secure it with the mounting bolts.
11. Reconnect the battery cable. Start the engine using a water supply (flushing muffs) and confirm a steady stream of water from the tell-tale outlet.

Troubleshooting & FAQ

Q: How do I confirm this kit fits my Honda engine?
A: This kit is designed for Honda BF8D, BF9.9D, BF15D, and BF20D series outboards. Please check the "Compatible Engine Models" table to verify your specific model and year. It's also critical to cross-reference the OEM part number 06192-ZW9-A30 with your existing part.

Q: My engine has a 25" extra long shaft. Will this kit fit?
A: There is conflicting information from different suppliers regarding shaft length compatibility. Some data indicates this kit fits extra long (25") shafts, while other sources state it will not. To ensure a correct fit, we strongly recommend verifying the required OEM part number for your specific engine's serial number before purchasing.

Q: What are the common signs of a failing water pump impeller?
A: The most common indicators include the engine overheating, a weak or non-existent water stream from the "telltale" cooling outlet, or finding that the old impeller's rubber vanes are cracked, brittle, or have broken off during inspection.

Q: How often should I replace the water pump impeller?
A: As a preventative maintenance measure, it is recommended to inspect the impeller annually and replace it every 1-2 years or every 100-200 hours of operation. Replacement intervals should be shorter for engines used frequently in saltwater or silty/sandy conditions.

Q: OEM vs. Aftermarket?
A: This listing is an aftermarket replacement part (not an OEM component). We build to OEM specifications using comparable-grade materials. Production is done in an ISO9002-certified facility, and each batch is inspected for consistent performance.

Q: How fast do you ship and how much does it cost?
A: We offer fast global shipping—typically 5–15 days worldwide—and standard shipping is free. Expedited options are available at checkout depending on your location.

Q: What is your warranty and return policy?
A: This product includes a 1-year warranty against manufacturing defects under normal use. If something goes wrong, contact our support team with your order details. Returns are accepted within our standard return window (unused & in original condition); please see our policy page or reach out for instructions.

Important Notes

• Verify that the product images and specifications match your original part. If discrepancies exist—even if your model is listed—do not proceed with the purchase.
• This product is an aftermarket replacement part and is not an OEM component.
• Professional installation is recommended to ensure safety and optimal performance.

Why Choose JLM MARINE?

• Quality Assured: As a trusted manufacturer for over 20 years, we supply top marine brands globally.
• Fast Global Shipping: Free delivery worldwide in 5–15 days.
• Direct from Manufacturer: Competitive pricing without compromising quality.