3/8" Snow Blower Impeller Modification Kit 3-Blade Universal - by Haiouus, for Modifies Snowblower 2-Stage Machine

3/8" Snow Blower Impeller Modification Kit 3-Blade Universal - by Haiouus, for Modifies Snowblower 2-Stage MachineBrand: Haiouus Features: Product Includs: 3 X Rubber Paddles 3 X Metal Straps 9 X Bolts 9 X Lock Nuts 3 X Self Tapping Screws 3 8" Thick Rubber Paddle (2"W X 5"L) (Trim To Fit As Needed). Made From Styrene Butadiene Rubber (Sbr Rubber) Sbr Rubber With Minimum Tensile Strength Of 725 Psi (5 Mpa),Hard Rubber With A Durometer Of 65 75. Metal Strap With Holes 1 3 8" W X 3 3 4"L ,1 16" Thick. Bolts (5 16 18 X 1 In. Coarse Thread) W 5 16 18 Lock Nuts (Use 1

Brand: Haiouus

Features:

• ☞Product Includs: 3 X Rubber Paddles 3 X Metal Straps 9 X Bolts 9 X Lock Nuts 3 X Self-Tapping Screws
• 3/8" Thick Rubber Paddle (2"W X 5"L) - (Trim To Fit As Needed). Made From Styrene Butadiene Rubber (Sbr Rubber) Sbr Rubber With Minimum Tensile Strength Of 725 Psi (5 Mpa),Hard Rubber With A Durometer Of 65-75. Metal Strap With Holes - 1 3/8" W X 3 3/4"L ,1/16" Thick. Bolts (5/16-18 X 1 In. Coarse Thread) W/ 5/16-18 Lock Nuts (Use 1/2" Wrench & Socket) ; Hex Bolts,Hex Lock Nuts Nylon Inser. Self-Tapping Screw (#14 X 1),Sheet Metal Screw, Hex Washer Head Self Drilling.
• ☞This Kit Is To Reduce The Existing“Gap”Between The Snow Blower'S Impeller Blades And The Impeller Chamber Wall. The Smaller The Gap, The Greater Your Machine'S Operational Efficiency And Snow Throwing Capability Will Be, And The Less Likely That Your Machine Will Clog Up With Snow. This "Gap" Allows Snow And Slush To Slip By The Blades And Build Up Around The Impeller And In The Discharge Chute Clogging It.
• ☞This Gap Also Decreases The Efficiency Of The Impeller'S Ability To Propel The Snow Up The Chute Resulting In Less Throwing Distance. If You Have A Single-Stage Snow Blower, Or Your Gap Is Less Than 1/4" Or Greater Than 5/8", You Probably Don'T Need Or Can'T Use This Fix.
• ☞If The Gap Varies Around The Chamber Wall, You Must Install The Rubber To Fit The Spot Where The Gap Is The Smallest, Otherwise, The Rubber Will Fail! The Rubber Paddles Mounted Should Be Installed So They Are Barely Touching. Remember, Any Decrease In The Gap Between The Impeller Blades And The Chamber Wall Will Result In A Significant Improvement In Operational Efficiency And Throwing Distance!

Details: This Kit Is To Reduce The Existing“Gap”Between The Snow Blower'S Impeller Blades And The Impeller Chamber Wall. The Smaller The Gap, The Greater Your Machine'S Operational Efficiency And Snow Throwing Capability Will Be, And The Less Likely That Your Machine Will Clog Up With Snow. This "Gap" Allows Snow And Slush To Slip By The Blades And Build Up Around The Impeller And In The Discharge Chute Clogging It. This Gap Also Decreases The Efficiency Of The Impeller'S Ability To Propel The Snow Up The Chute Resulting In Less Throwing Distance. This Problem Is Well Known To People With Two-Stage Snow Blowers, And The Easy And The Quick, Inexpensive Fix Is To Modify The Impeller Blades By Adding A Strip Of Reinforced Rubber To Each One Of Them To Eliminate This Gap. It Is Highly Recommended That You Install One Kit On Each Blade However, Because Only Modifying Some But Not All Of The Blades Will Cause A Harmonic Imbalance In The Spinning Impeller Which Could Easily Cause Excessive Wear On The Impeller Shaft Bearing Resulting In Very Costly Repairs!