Happymodel Mobula8 2S Digital HD (Walksnail Avatar) 85mm Micro FPV Whoop Drone - ELRS 2.4

Happymodel Mobula8 2S Digital HD (Walksnail Avatar) 85mm Micro FPV Whoop Drone - ELRS 2.4Here comes Mobula8 2S Digital HD FPV series with Walksnail Avatar System, New CrazyF405 ELRS flight controller, EX1103 KV11000 motors and Gemfan Hurricane 2023 tri blade propeller, which has excellent power performance and extremely smooth flight in HD Quality Video. Here is our recommended 2S 550mAh Battery that fits perfectly in this drone! Check out our Micro Whoop Drones, our entire Happymodel Products and The Digital BNF PNP RTF Collection.

Here comes Mobula8 2S Digital HD FPV series with Walksnail Avatar System, New CrazyF405 ELRS flight controller, EX1103 KV11000 motors and Gemfan Hurricane 2023 tri-blade propeller, which has excellent power performance and extremely smooth flight in HD Quality Video.

Here is our recommended 2S 550mAh Battery that fits perfectly in this drone!

Check out our Micro Whoop Drones, our entire Happymodel Products and The Digital BNF/PNP/RTF Collection.

Features:

• Digital HD FPV experience
• New CrazyF405 ELRS HD flight controller
• Powerful and Smooth
• UART ExpressLRS receiver
• Built-in blackbox for Gyroflow and PID Tune

Specifications:

Motor

• Mode: EX1103 KV11000
• Configu-ration:9N12P
• Stator Diamter:11mm
• Stator Length:3mm
• Shaft Diameter:Φ1.5mm
• Motor Dimension(Dia.*Len):Φ13.5mm*15.5mm
• Weight(g):3.8g
• No.of Cells(Lipo):1-2S

Propellers

• Weight:0.88g
• Material: PC
• Pitch:2.3inch
• Props Dia:52.17mm
• Center Thickness:5mm
• Center Hole Dia:1.5mm

Flight Controller

• MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
• GYRO Sensor: BMI270  (SPI connection)
• Mount hole size: 25.5mm*25.5mm
• Power supply: 1-2S battery input (DC 2.9V-8.7V)
• Built-in 12A(each) Blheli_S 4in1 ESC
• Built-in Serial ExpressLRS 2.4G
• Built-in BMP280 Barometer
• Built-in 8MBp blackbox
• Built-in voltage meter sensor , voltage meter scale 110
• Built-in current meter sensor , current meter scale 470

Onboard 4in1 ESC

• Power supply: 1-2S LiPo/LiPo HV
• Current: 12A continuous peak 15A (3 seconds)
• Support BLHeli_S Bluejay firmware
• Factory firmware: Bluejay ESC V0.19
• Firmware target: Z-H-30
• Default protocol: DSHOT300
• When use 1s battery and high KV 0702/0802 motors, should set startup power to 1100/1200

Onboard UART ExpressLRS 2.4GHz Receiver

• Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
• RF Frequency: 2.4GHz
• Antenna: enameled copper wire 31mm length
• Telemetry output Power: <12dBm
• Default firmware version: ExpressLRS V3.0.1
• Firmware target: HappyModel EP 2400 RX
• Could update firmware via ExpressLRS configurator

** If bound to radio but having trouble seeing stick movement in Betaflight, then you may need to turn off the "Model Match" factory setting in the ELRS web GUI.

Walksnail version

• Camera Model       Avatar lite camera
• Image Sensor     1/2.7”1nch
• Resolution          1080P/60fps,720P/120fps,720P/60fps
• Ratio      16/9  4/3
• Lens          2.1mm
• FOV         170°
• Aperture            F2.0
• Rolling shutter
• Min.Illumination  0.001Lux
• Weight       1.8g
• Dimensions        14*14*16mm
• VTX Model        Avatar mini 1s module
• Communication Frequency    5.725-5.850GHz
• Transmitter Power (EIRP)       FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm;
• MIC:<25dBm
• I/O Interface        JST1.0*6(Power in)JST0.8*4(USB)
• Mounting Holes   25.5*25.5mm
• Dimensions         30*30*6.5mm
• Storage      8G
• Recording  1080p/720p
• Weight       5.1g
• Operating Temperature  -20-40℃
• Channels    8
• Wide Power Input         3.1V-5V
• Supported FC System  Betaflight
• OSD  Canvas mode
• Bitrate        25mbps 50mbps
• Latency      Average delay 22ms
• Antenna      IPEX 

 Package Includes:

• 1x Mobula8 Frame
  
• 1x CrazyF4HD ELRS flight controller firmware target:BETAFLIGHTF4
• 4x EX1103 KV11000 brushless motor
• 1x Gemfan Hurricane 2023 tri-blade propellers(4cw+4ccw)
• 1x Walksnail avatar HD Mini 1S lite kit
• 1x Canopy(DJI O3/Walksnail/HDZERO optional)
  
• 1x Screw driver