Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 14 - Jul 19
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Tapping chucks for synchronisation BT 50 - M3-M12 - 95 | ER 16Application: For machining centres with synchronous spindle. Note: Synchro tapping chucks compensate synchronisation errors. Minimal length compensation on compression and expansion balances very small pitch differences between synchro spindle and tap, which can cause high frictional forces on the thread flanks. A possible increase of axial force during the tapping process is reduced to a minimum. Suitable for internal coolant. Coolant pressure up to
Application:
For machining centres with synchronous spindle.
Note:
- Synchro tapping chucks compensate synchronisation errors.
- Minimal length compensation on compression and expansion balances very small pitch differences between synchro spindle and tap, which can cause high frictional forces on the thread flanks.
- A possible increase of axial force during the tapping process is reduced to a minimum.
- Suitable for internal coolant.
- Coolant pressure up to max. 100 bar.
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm² after DIN
- All functional surfaces fine machined
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.5 ★★★★★
Based on 1670 reviews
Sort
Product Reviews
★★★★★ 5
Direct replacement on my 95 SeaRay 175
Size: PP67-712 V1
My boat started to have issues with not turning over when I used the ignition switch. Replaced the switch and had no effect. Replaced the solenoid and that fixed the problem. Good price, so I replaced all 3 solenoids (Trim/ starter). Solenoids had all needed hardware (nuts/washers)
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 9, 2024
★★★★★ 5
They Fixed My Boat
Size: PP67-712 V1
My boat wouldn’t start, and the outdrive wouldn’t go up or down. So I bought three of these solenoids and replaced the starter and both trim motor solenoids/relays. Now it starts right up with no problems and the trim motor is working again also. I have a 2006 Stingray boat.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 7, 2022
★★★★★ 1
Poor quality
Size: PP67-712 V1
Poor quality. Replaced a starter solenoid on a mercruser 4.3. Right off install it would click but not make a connection to start motor. Confirmed this was the culprit by jumping the terminals. After testing multiple times found it worked a little less than half the time.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 29, 2026
★★★★★ 5
Best main wire for price
Size: 25 FT, Style: 0 (1/0) AWG RED
Good main wire and is accurate size and length
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 18, 2026
★★★★★ 5
Cables buenas
Size: 25 FT, Style: 0 (1/0) AWG RED
Excelente 👌
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 9, 2026