SKY RC S100 Neo AC/DC 100/200w ChargerSKY RC S100 Neo AC DC 100 200w Charger The small SKY RC S100neo 200W charger has been designed to provide everything you need for charging, including a powerful mains power supply, with simple operation. The S100neo allows you to charge and discharge common types of cells (NiCd, NiMH, Li poly, Li ion, Li Fe, Li HV, Pb) and is equipped with a built in powerful six channel balancer (1 A cell), which ensures very safe and comfortable charging of lithium

• SKY RC S100 Neo AC/DC 100/200w Charger

• The small SKY RC S100neo 200W charger has been designed to provide everything you need for charging, including a powerful mains power supply, with simple operation. The S100neo allows you to charge and discharge common types of cells (NiCd, NiMH, Li-poly, Li-ion, Li-Fe, Li-HV, Pb) and is equipped with a built-in powerful six-channel balancer (1 A/cell), which ensures very safe and comfortable charging of lithium batteries. It can also operate in regulated power supply mode with an output voltage adjustable from 2 to 30 V and a current limit of 0.1 to 12 A.

  The intelligent software offers the usual functions and is designed for practical users who purchase the charger to charge batteries:

   

  • programme for new types of ‘high-voltage’ LiHV lithium batteries with a charging cut-off voltage of up to 4.35 V
  • setting of the end voltage for charging and discharging lithium batteries (allows gentler charging, which is preferred by pilots, or, conversely, overcharging, which is preferred by car enthusiasts - max. 4.22V for LiPo, 4.12V for Li-ion, 3.67V for LiFe, 4.37V for LiHV with current firmware)
  • programmes for charging maintenance-free lead-acid AGM batteries and charging lead-acid batteries at low temperatures
  • measurement of total voltage and individual cell voltage (for lithium batteries), even outside charging/discharging - and even without the need for a power supply: the S100neo can function as a stand-alone tester powered by the battery under test
  • measurement of the internal resistance of the entire set and individual cells (for lithium batteries)
  • Special programme for running in DC motors (for a selected time at a set voltage and current)
  • Socket for temperature sensor for safe charging of NiMH batteries

   

  Overview of basic functions and parameters
  

  • Input supply voltage 6–30 V DC (for full use of the charger's power, the power supply should provide at least 24 V) when powered from a battery or mains stabilised power supply
  • Mains power supply 100–240 V/50–60 Hz
  • For charging and discharging 1–15 NiCd/NiMH cells, 1–6 Li-ion/Li-poly/Li-Fe/LiHV cells or 6/12/24 V lead-acid batteries with liquid electrolyte and maintenance-free AGM
  • Adjustable charging current 0.1–12.0 A
  • Adjustable discharge current (0.1–2.0 A)
  • Max. charging power 200 W when powered from an external mains supply or car battery, or 100 W when powered from the built-in mains supply
  • Max. discharge power 5 W
  • Automatic delta-peak termination for NiCd and NiMH batteries
  • Lithium and Pb batteries are charged using the ‘constant current/constant voltage’ method
  • Adjustable delta-peak detection sensitivity for NiCd and NiMH batteries
  • Adjustable end voltage for charging and discharging lithium batteries
  • Repeated cyclic charging/discharging or discharging/charging for NiCd and NiMH batteries, up to 3 cycles
  • Three charging modes for lithium batteries - normal charging, charging with emphasis on balancing and storage charging/discharging
  • Three charging modes for lead-acid batteries - for normal lead-acid ‘car batteries’, for lead-acid AGM batteries (batteries with electrodes separated by a glass fibre separator impregnated with electrolyte) and for charging lead-acid batteries at low temperatures (-20 °C to +5 °C).
  • Charging stops when the set time, temperature (for NiMH/NiCd) or charge is exceeded
  • Measurement of the total voltage of the set and individual cells (for lithium batteries)
  • Measurement of total internal resistance of the set and individual cells (for lithium batteries) - The S100neo can also function as a stand-alone tester powered by the battery under test
  • Stabilised mains supply mode with adjustable voltage and current limitation 2–30 V/0.1–12 A, max. 100 W when connected to mains/max. 200 W when powered from an external source
  • DC motor running-in mode for optimal mutual adjustment of carbon brushes and commutator (motor runs for a selected time at the set voltage and current)
  • USB-C port for charger firmware updates
  • Socket for temperature sensor
  • Backlit LCD with simple and clear menu and parameter display during charging/discharging
  • Several warning messages contribute to safe operation – incorrect input voltage, incorrect connection, unsuitable battery or its condition, incorrect polarity at the output, etc.
  • Protection against reverse polarity and short circuit at the output.
  • Fan for forced cooling.
  • Compact plastic housing, small dimensions

   

  The charger is equipped with an XT60 output socket and a universal socket for JST-XH service connectors, allowing direct connection of battery power cables and JST-XH service connectors from 2-6S sets – if you use sets with XT60 and JST-XH connectors, you can do without charging cables and adapters. To connect service connectors from other systems, you can use standard Sky RC or RC System adapters.

  Note: When charging lead-acid batteries, the charger uses a cut-off voltage of 2.40 V/cell (or 2.46 V/cell in the AGM battery programme and in the cold charging programme) – for this reason, it is suitable for charging conventional lead-acid batteries (car batteries) and gel batteries with a reversible valve. It is not suitable for charging gas-tight gel batteries, which must not be charged to more than 2.30 V/cell.

  The charger set includes: S100neo charger, mains cable, instructions.