SKU: 89277407933

Blackmagic Design Spares - ATEM 2M/E Prod Studio 4K - PCB SDI

Sale price$4091.87 Regular price$4546.52
Save 10%

Pay in installments of $1136.63 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 21 - Aug 26

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Blackmagic Design Spares - ATEM 2M/E Prod Studio 4K - PCB SDIThe Blackmagic Design Spares ATEM 2 M E Production Studio 4K PCB SDI is the specific I O interface board (often referred to as the "SDI Board" or "Connector PCB") that populates the rear of the unit. In the ATEM 2 M E 4K architecture, this board is distinct from the Main processing logic, focusing entirely on high frequency signal distribution for the 20 SDI inputs and various SDI outputs. Because this board handles 6G SDI or 12G SDI signals

The Blackmagic Design Spares - ATEM 2 M/E Production Studio 4K - PCB SDI is the specific I/O interface board (often referred to as the "SDI Board" or "Connector PCB") that populates the rear of the unit. In the ATEM 2 M/E 4K architecture, this board is distinct from the Main processing logic, focusing entirely on high-frequency signal distribution for the 20 SDI inputs and various SDI outputs.

Because this board handles 6G-SDI or 12G-SDI signals (depending on the specific hardware revision), it is a high-precision component where the physical layout of the traces is critical to preventing signal "jitter" or data loss.


Core Responsibilities

  • SDI Input Bank: Manages the 20 physical BNC inputs. It handles the signal equalization required to "clean up" incoming video that has traveled over long cable runs.

  • Return/Aux Outputs: Houses the BNC connectors for the 6 Aux outputs, Program out, and Preview out.

  • Signal Re-clocking: Every port on this board has a dedicated "Re-clocker" chip. This ensures that the output signal leaving the switcher is as strong and stable as the original source.

  • 6G/12G-SDI Support: Manages the massive bandwidth required for Ultra HD 4K video. If this board fails, you may see signals working in 1080p but failing immediately when the switcher is set to a 4K resolution.


When to Replace the SDI PCB

  • "Dead" Port Rows: If a horizontal row of BNC ports (e.g., all the even-numbered inputs) stops working, the power rail or controller chip on the SDI board has likely failed.

  • Physical BNC Fatigue: The SDI PCB is the most common part to break due to mechanical stress. If a BNC connector is "spinning" or has been pushed into the chassis, the solder pads on the PCB are likely torn.

  • Sparking/Static Damage: SDI ports are "hot-pluggable," but a significant voltage difference between a camera and the switcher can fry the input protection diodes on this specific board.

  • BNC Center-Pin Damage: If a user accidentally inserts a damaged SDI cable and snaps the "female" center pin of the BNC port, the entire SDI board is usually replaced to ensure broadcast reliability.


Technical Installation Note

Repair Level: 4 (Advanced). 1. The Nut Marathon: You must remove the silver hex nuts and washers from all 20+ SDI connectors on the rear. Use a proper $14\text{mm}$ socket. Pro-Tip: Do not use pliers, as you will scratch the black paint of the chassis, which can devalue the unit for resale.

2. Ribbon Cable Interconnects: The SDI PCB connects to the Main PCB via several high-density ribbon cables or "flex-circuits." These are extremely fragile. Ensure you unlatch the "ZIF" (Zero Insertion Force) connectors before pulling the cables.

3. BNC Alignment: When sliding the new board in, all 20+ BNC ports must line up with the back panel holes simultaneously. It is a tight fit. If it doesn't slide in easily, check that a ribbon cable isn't pinched between the board and the chassis.

4. Static Control: This board is covered in sensitive CMOS chips. Wear an ESD wrist strap; one static pop can kill an input before you even finish the repair.


Diagnostic: SDI Board vs. Main PCB

  • It's the SDI Board if: The ATEM Software Control shows that the switcher is alive, the Multiview UI is visible, and the internal Media Pool graphics can be keyed over "Black," but your external SDI cameras show no signal.

  • It's the Main PCB if: The software won't connect, or the entire Multiview output is missing/garbled.

Expert Advice: If you are replacing this board due to physical damage, consider installing a 1RU or 2RU BNC Patch Panel in your rack. By plugging your cameras into a patch panel instead of directly into the SDI PCB, you transfer the "wear and tear" to an inexpensive patch cable rather than the expensive internal SDI board.

Are you experiencing a loss of signal across all ports, or is one specific BNC connector physically damaged?

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 89277407933

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.1 ★★★★★
Based on 19 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
B
Brooke Gilman
Belleville, US
★★★★★ 1
0/10 chance it’ll actually hold your phone
Instillation- easy. Function- terrible, it didn’t hold my phone up for more than 2 seconds before the entire holder fell down (IPhone 16 pro; 7.5oz with a slim case.) Fit- great but useless for the durability.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 14, 2026
H
Verified Purchase
Holly Hamblin
Omaha, US
★★★★★ 1
Not Worth it
This mount was great for about a week. After that it popped off and would not stay in place. I would not recommend buying this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 25, 2026
C
Verified Purchase
Connie
Alexandria, US
★★★★★ 1
Waste of Money
Worked great for about a week and then came off. It won’t clip back on now.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 9, 2026
T
Verified Purchase
Tanisha Barnwell
Battle Creek, US
★★★★★ 1
Keeps dropping
It’s not staying latch. It keeps dropping.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 18, 2026
L
Verified Purchase
Laxraddad
Louisville, US
★★★★★ 5
Rare accessory for VW Arteon
Size: 2019-2020 Arteon
After market items made specifically for the 2019-2020 VW Arteon are rare. Picked it up quickly!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 14, 2024

recommand products