Cisco 10G EP, SFP+ 1560.61, 100 GHz, LC

Powerful, scalable, and engineered for high-density data networking, the Cisco 10G EP SFP+ 1560.61 100 GHz LC transceiver delivers dependable 10 Gigabit Ethernet performance over DWDM networks. Designed for data centers, campus networks, and service-provider backbones, this SFP+ module leverages dense wavelength-division multiplexing to maximize fiber capacity without adding more fiber strands. With a center wavelength of 1560.61 nm and a 100 GHz ITU grid, it enables precise channel placement across long-haul links while preserving compatibility with Cisco switches and routers that support SFP+ DWDM optics. The compact LC duplex interface makes installation straightforward in crowded data center racks and CU/edge deployments, while the single-mode fiber compatibility reduces attenuation and allows for longer reach between network elements. Whether you are building optical rings, backbone interconnects, or data center interconnects, the Cisco 10G EP SFP+ 1560.61 100 GHz LC transceiver is crafted to boost bandwidth, simplify upgrades, and lower total cost of ownership through efficient utilization of existing fiber infrastructure.

• High-capacity 10GBase-DWDM performance to extend uplinks and interconnects without adding fiber you don’t have.
• Precise 1560.61 nm center wavelength paired with 100 GHz ITU channel spacing for dense WDM deployments.
• Compact SFP+ form factor with LC duplex connector for easy hot-swapping and seamless integration into Cisco devices.
• Optimized for single-mode fiber with low insertion loss and strong optical performance across typical DWDM links.
• Designed for data networking and optical networks, delivering reliable 10 Gbps throughput with low latency and broad Cisco compatibility.

Technical Details of Cisco 10G EP, SFP+ 1560.61, 100 GHz, LC

• Product type: SFP+ transceiver for 10GBase-DWDM
• Wavelength (center): 1560.61 nm
• ITU channel spacing: 100 GHz
• Data rate: Up to 10 Gbps
• Fiber type: Single-mode fiber (SMF)
• Connector: LC duplex
• Interface: SFP+ hot-swappable module compatible with Cisco network equipment supporting DWDM optics
• Application: Data networking and optical network backbones, data center interconnects, and campus networks

How to install Cisco 10G EP, SFP+ 1560.61, 100 GHz, LC

• Prepare the host device: Verify that the Cisco switch or router supports SFP+ DWDM transceivers and that the port is enabled for 10G operation.
• Power and safety: If your equipment supports hot-swapping, you can install the transceiver without powering down the entire device; otherwise follow your vendor’s service procedures.
• Insert the transceiver: Remove protective caps, align the module with the SFP+ slot, and insert firmly until it seats with a tactile click. Do not force the module.
• Connect fiber correctly: Use single-mode fiber with LC duplex connectors. Ensure that both ends are terminated with LC duplex DWDM transceivers configured for matching wavelengths and channel spacing (1560.61 nm, 100 GHz).
• Verify link and performance: After installation, check the optical link status on the switch/router, confirm light/activity indicators, and run basic tests (link up, keepalive, and throughput tests) to validate performance.

Frequently asked questions

• What is Cisco 10G EP, SFP+ 1560.61, 100 GHz, LC?

A 10 gigabit DWDM SFP+ transceiver with a center wavelength of 1560.61 nm and 100 GHz ITU channel spacing, designed for data networking and optical networks, using an LC duplex connector for single-mode fiber and enabling high-capacity DWDM links in Cisco environments.

• What fiber and connector does it use?

It uses single-mode fiber (SMF) with an LC duplex connector, which is common for long-haul DWDM deployments and ensures low loss and broad reach when paired with appropriate DWDM systems.

• Which devices are compatible?

Compatible with Cisco devices that support SFP+ DWDM optics and 10GBASE functionality. Always verify that the specific chassis, line card, and software version support DWDM transceivers of this type.

• How far can it transmit data?

The achievable distance depends on fiber quality, OSNR, dispersion management, and the network design. DWDM transceivers like this are typically used for links spanning several kilometers to tens of kilometers, but exact distances should be confirmed against Cisco and vendor specifications for your deployment scenario.

• Can I mix this with non-Cisco DWDM transceivers?

Interoperability with non-Cisco DWDM hardware is not guaranteed. For best results and support, use transceivers and components within the same vendor portfolio or confirmed interoperable configurations. Always consult your network design and vendor guidance.

• Is this module hot-swappable?

Yes. SFP+ modules, including Cisco DWDM transceivers, are designed to be hot-swappable in most modern Cisco devices, enabling maintenance with minimal downtime.

• What are the security and reliability considerations?

DWDM transceivers are designed to be robust in enterprise and service-provider environments. Ensure proper physical security of fiber connections, proper enclosure for outdoor or harsh environments if applicable, and monitoring via your network management system to detect LOS (loss of signal) and performance changes.