Advantech EKI-2701HPI PoE Injector

The Advantech EKI-2701HPI PoE Injector is a compact, reliable solution designed to simplify modern network deployments by delivering both data and power over a single Ethernet cable. Built to IEEE 802.3af/at standards, this injector empowers a wide range of PoE-enabled devices—such as IP cameras, wireless access points, IP phones, and industrial sensors—without the need for separate power cabling. Its streamlined design makes installation straightforward in both enterprise and industrial environments, enabling fast, scalable setups while maintaining robust performance and safety. Whether you’re outfitting a small office, a classroom, or a factory floor, the EKI-2701HPI helps you deploy devices quickly, reduce cable clutter, and future-proof your network as you add more PoE devices over time.

• Single-port PoE injector that powers a PoE-enabled device through a single Ethernet cable, reducing cable clutter and simplifying installation and maintenance.
• IEEE 802.3af/at compliant: supports standard PoE and higher-power PoE devices, enabling a broad range of devices such as IP cameras, wireless APs, and VoIP phones while protecting network safety.
• Flexible power architecture and reliable data transmission: delivers data and power together over CAT5/CAT5e/CAT6 cables, providing a dependable link from your switch to the powered device with minimal setup steps.
• Clear diagnostics with LED indicators: independent status LEDs for power, link, activity, and PoE output help technicians quickly assess health and troubleshoot issues on-site.
• Compact, versatile installation: designed for easy integration in cabinets, on desks, or in wall-mounted enclosures; suitable for DIN rail or wall-mount configurations where supported by your installation environment.

Technical Details of Advantech EKI-2701HPI PoE Injector

• PoE Standard: IEEE 802.3af/at
• PoE Port: 1 output port for delivering power and data to a PoE-enabled device
• Data Rate Support: standard Ethernet compatibility (10/100 Mbps)
• Power Input: external DC power supply required to enable PoE output
• Power Output to Device: PoE over the RJ-45 output port, delivering data + power to connected devices
• Physical Form: compact injector suitable for installation in customer environments; designed for reliable operation in typical office and industrial settings
• Indicators: LED indicators for Power, Link, Activity, and PoE status to simplify monitoring
• Safety & Compliance: built to meet common safety and environmental standards typical for PoE devices
• Mounting: compatible with common mounting practices for network peripherals (DIN rail and/or wall-mount as suited to the application)

How to Install Advantech EKI-2701HPI PoE Injector

• Plan the placement of the injector in a secure, accessible location near your network equipment. Ensure adequate airflow and protection from moisture or excessive dust to maintain long-term reliability.
• Connect a CAT5/6 Ethernet cable from your network switch to the injector’s data input port. This provides the data path to the injector before it is delivered to the powered device.
• Connect the PoE-enabled device (such as an IP camera or wireless access point) to the injector’s PoE output port using a CAT5/6 cable. This is the single cable that will carry both data and power to the device.
• Connect the external DC power supply to the injector’s power input. Use the power adapter specified by Advantech for the EKI-2701HPI and verify that the voltage and current meet the device’s requirements.
• Power on the injector and observe the LED indicators. A steady power LED along with active link and PoE LEDs indicates that power is flowing and that the connected device is communicating properly. If any indicator shows an issue, re-check cabling and power connections.
• Secure the unit in place. If mounting is available, use DIN rail or wall-mount hardware as recommended by the product’s installation guides. Route cables neatly to avoid strain and to maintain a clean, professional installation that minimizes interference and accidental disconnections.

Frequently asked questions

• Q: What devices can be powered by the Advantech EKI-2701HPI PoE Injector?
• A: The injector powers PoE-enabled devices such as IP cameras, wireless access points, VoIP phones, and other IEEE 802.3af/at compliant devices that can receive power over Ethernet.
• Q: Does the injector support both IEEE 802.3af and IEEE 802.3at?
• A: Yes. It is designed to be compatible with both standards, allowing it to power a wide range of devices with different power requirements.
• Q: How many devices can be powered with this injector?
• A: The Advantech EKI-2701HPI provides a single PoE output port, capable of powering one PoE-enabled device at a time. For multiple devices, a PoE switch or additional injectors would be required.
• Q: Is external power always required for PoE delivery?
• A: Yes. An external DC power supply powers the injector and enables PoE output through its RJ-45 PoE port. Without the external supply, the injector will not deliver PoE to devices.
• Q: What installation considerations should I keep in mind?
• A: Ensure proper cable management, secure mounting where applicable, and verify that the total power budget matches the needs of your PoE device. Use quality CAT5/6 cables, and monitor LED indicators during initial setup to confirm proper operation.