D8T Truggy Kit, 1/8 scale, Nitro

D8T Truggy Kit, 1/8 scale, NitroThis is the 1 8 scale, glow powered, radio controlled, Hot Bodies off road D8T Truggy Kit. FEATURES: Chassis: 0. 16" (4mm) thick 7075 aluminum with 10 of kickup, composite chassis braces Drive: Four wheel shaft drive Fuel Tank: 5. 1oz (150cc) plastic with flip top cap Air Filter: Foam low profile design Clutch: 3 shoe, carbon construction Clutch Bell: 13 tooth steel Transmission: Single speed Ball Bearings: Full set Shocks: Four oil filled, 16mm Big

This is the 1/8 scale, glow powered, radio controlled, Hot Bodies off-road D8T Truggy Kit. FEATURES: Chassis: 0.16" (4mm) thick 7075 aluminum with 10° of kickup, composite chassis braces Drive: Four wheel shaft drive Fuel Tank: 5.1oz (150cc) plastic with flip top cap Air Filter: Foam low profile design Clutch: 3 shoe, carbon construction Clutch Bell: 13 tooth steel Transmission: Single speed Ball Bearings: Full set Shocks: Four oil-filled, 16mm Big Bore aluminum bodied Main Gear: 50 tooth steel Gearboxes: Sealed Differentials: Planetary Brakes: Dual fiber discs Wheels: White plastic dish wheels, 3.7" (95mm) diameter, 2.3" (58mm) wide, 17mm hex Body: Clear untrimmed polycarbonate truggy body Bumpers: Front hardened plastic Suspension: Captured hinge pin design, extra wide pivot block for optimized geometry Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis Camber: Adjustable, camber refers to the angle of the tops of the tires from vertical when viewed from front or behind vehicle Steering: Bell crank type with servo saver Warranty Period: Two year limited, valid only in the U.S. Canada, and South America INCLUDES: 1/8 scale Hot Bodies off-road Truggy Kit, foam air filter, body, wheels, rear wing, clutch bell, spur gear, instructions and decal sheet REQUIRES: Radio: 2-Channel with 2 Servos (one high torque servo for steering) Radio Batteries: (8) AA size Receiver Pack: 6V hump Engine: .21 cu in (3.4cc) rear exhaust Exhaust: Tuned pipe Engine Starter: Hand-held type with rubber adapter for vehicle use Tires: 1/8 scale off-road truggy Glow Starter: 1.2 volt Paint: Polycarbonate safe for body Misc. Items: Fuel bottle, building and track equipment Fuel: 2-cycle glow fuel with 10%-15% nitromethane, 16% lubricant- Most of the fuels we carry meet or exceed the lubricant content required for optimum performance and maximum engine life. In the past, the conventional lubricant content used in fuel was 18%. But with new advanced technologies, fuels like Red Alert and O'Donnell for example, have a better quality of lubricants even though the percentages of lubricant content are lower. These high-tech lubricants provide exceptional cooling and protection. SPECS: Vehicle- Length: 21" (530mm) from front bumper to end of rear wing Width: 15.9" (405mm) Weight: 9lbs (4082g) approximately Wheelbase: 15-15.1" (380.5-383.5mm) wheels on-center front-to-rear Gear Ratio: 4.3:1 Body- Length: 18.2" (462mm) Width: 7.4" (188mm) at middle section (widest point) 6.9" (175mm) ahead of front wheels (thinnest point) Height: 4.1" (105mm) COMMENTS: For Replacement Ball Bearings use: Qty. Size Location Qty. Bearing Set 2 6x10mm Steering 1 DTXC1561 6 8x16mm Diffs 3 DTXC1585 2 5x11mm Clutch 1 DTXC1547 4 8x14mm Front Hubs 2 DTXC1583 4 8x14mm Rear Hubs 2 DTXC1583